Quantitative Determination of Sulphate

Quantitative Determination of SulphateQuantitative Determination of Sulphate by hydrometric AnalysisYeo Yi JoshuaGravimetric depth psychology is a quantitative method to determine the bar of a substance, sulphate, by selective precipitation of the substance from an aqueous dissolving agent. In this experiment, the amount of sulphate is determined quantitatively as barium sulphate, BaSO4 by hydrometric analysis.This experiment pull up stakes allow one to determine the amount of sulphate SO42- by the gravimetric method. This determination is do by slowly adding a dilute solution of barium chloride, BaCl2 to a hot un cognise sulphate slightly acidified with concentrated HCl. The reaction is as followed, Ba2+ + SO42- BaSO4 ( innocence abrupt). The discolour precipitate is so filtered off, washed with water, dried in the oven, and weighed as barium sulphate. The percentage of sulphate is then calculated from the weight of barium sulphate.According to the results, the tightness of SO42- we obtained was 0.0345M and 3.31 g/L, which was close to the theoretical value of 3.38 g/L, at only a exit of 2.11%. The experiment was prosperous and the results obtained were desirable.The objective of the experiment is to determine the amount of sulphate by the gravimetric method.In this experiment, the precipitation gravimetric method is used. The unknown sulfate solution is converted into an insoluble white compound, BaSO4. It is then filtered by suction filtration, washed, dried and weighed to determine the amount of sulphate. The following diagram shows the out(a)line of the experiment.3.1 Gravimetric AnalysisGravimetric analysis is defined as the quantitative analysis of the chemical composition of substances of squares based on the separation of each component of interest and weighting either the purified compound or a derivative of it.Gravimetric analysis include precipitation, volatilisation and electro-analytical methods.The precipitation method involves conver ting the analyte to a sparingly soluble precipitate which is then filtered, washed free of impurities and converted to a compound of known composition by suitable heat treatment which can be weighed.The volatilisation method involves volatilising the analyte of its decomposition products at suitable temperature. The product is then collected and weighed or alternatively determined indirectly from the loss in mass of the sample.The electro-analytical method involves the depositing electrically the element to be estimated on a suitable electrode, avoiding filtration and decomposition, by unequivocal the experimental conditions. This is based on Faradays Second Law, i.e. when a haltn current is passed in series by the solution stocking various ions, the amount of substances that is deposited will be in the ratio of their chemical equivalent.In this experiment, the quantitative determination of sulfate, as barium sulfate BaSO4, is done by the precipitation method of gravimetric anal ysis. This involves precipitation by slowly adding a dilute solution of barium chloride, BaCl2, to a hot unknown sulfate solution slightly acidified with concentrated hydrochloric acid, HCl. The white precipitate is filtered off, washed with water, dried in the oven, and weighed as barium sulfate. The percentage of sulfate is then calculated from the weight of barium sulfate, this include the molarity and intentness of sulfate, SO42-, in g/L.3.2 ReactionIn the experiment, dilute barium chloride is added to an unknown sulfate solution slightly acidified with concentration HCl.Reaction Ba2+ + SO42- BaSO4 (precipitate) The mole ratio of SO42- BaSO4 is 11. Thus, for every 1 mole of SO42-, there will be 1 mole of BaSO4.Since Moles of Solute (mol) = Molarity (M) x Volume (L) and Moles of Solute (mol) = Weight (g) Molar Mass (g/mol), the molarity of SO42- can be easily obtained with the volume of SO42- weight of BaSO4 and molar mass of BaSO4.3.3 Precipitation3.3.1 Conditions of Precip itationPrecipitating agent should be mixed slowly and with unbroken agitation. This keeps the degree of supersaturation small and will help in the formation of lechatelieriteline precipitate.Precipitation should be carried out in dilute solution.Precipitation should be carried out in hot solution, provided the precipitate is stable at higher temperature.Crystalline precipitate should be digested for a longer era.Precipitates should be preferable washed with dilution solution of appropriate electrolyte. Washing with water is avoided as it leads to peptisation.Precipitates that argon contaminated by co-precipitation or others are dissolved in a suitable solvent and then reprecipitated from the solution.3.3.2 Properties of PrecipitatesPrecipitate should be of sufficiently low solubility such that no sufficient loss of the unattackable occurs during filtration and washingPhysical nature of the precipitate should be such that it can be readily separated by filtration and be washed f ree of soluble impurities i.e. particles should be size such that they cannot pass through the filtering media and particle size is unaffected by washingPrecipitate should be stable and unreactive to atmospheric conditionsPrecipitate must be convertible to a pure compound of definite and known chemical composition. This may be possible by either ignition or by simple feat such as evaporation.3.3.3 Particle Size of PrecipitatesThe particle size of a precipitate is influenced by precipitate solubility, temperature, reactant concentrations, and the rate at which reactants are mixed. The net meat of these variables can be qualitatively accounted for by assuming that the particle size is related to a single property of the system called relative supersaturation.Q is the concentration of the solute at any instance and S is the equilibrium solubility. This equation is known at the Von Weimarn equation in recognition of the scientist who proposed it in 1925. The particle size of a precipi tate varies inversely with the average relative supersaturation during the time when the reagent is being introduced. Thus, when the relative supersaturation is large, the precipitate tends to be colloidal, and when the relative supersaturation is small, a crystalline substantialness is more likely. A colloid consists of solid particles with diameters that are less than 10-4 cm.3.3.4 Mechanism of PrecipitationA supersaturated solution is an unstable solution that contains a higher solute concentration than a precipitated solution. As wastefulness solution precipitates with time, supersaturation decrease to zero.Precipitates form by nucleation and by particle growth. Nucleation is a process in which a minimum number of atoms, ions, or molecules join in concert to give a stable solid. These nuclei form on the come in of the suspended solid contaminants, such as dust particles. Further precipitation then is governed by the competition amidst additional nucleation and growth of exis ting nuclei (particle growth).Adsorption is a process in which a substance (gas, liquid or solid is held on the surface of a solid. In contrast, absorption is retention of a substance within the pores of a solid. The charge on a colloidal particle organise in a gravimetric analysis is determined by the charge of the lattice ion that is in excess when the precipitation is complete.Digestion is a process in which a precipitate is heated in the solution which is was formed (the bugger off liquor) and allowed to stand in contact with the solution. Mother liquor is the solution from which a precipitate was formed. Digestion improves the rectitude and filterability of both colloidal and crystalline precipitates.4.1 Outline4.1 Precipitation of BaSO44.2 Washing and Filtering BaSO4 Precipitate4.3 Drying and Weighing BaSO4 Precipitate5.1 WeightsWeight of crucible with the precipitate = 17.7473gWeight of crucible (with a piece of filter paper) = 17.5462g Weight of BaSO4 precipitate = Weight of crucible with the precipitate Weight ofcrucible (with a piece of filter paper)= 17.7473g 17.5462g= 0.2011 g5.2 Molarity and preoccupancyBa2+ + SO42- BaSO4 (precipitate) (Mol Weight BaSO4 = 233.33 g/mol) Molarity of SO42- = 0.0344747 M= 0.0345 M Concentration of SO42- in g/L = Molarity of SO42- x Mol wt of SO42-= 3.313026 g/L= 3.31 g/L6.1 Theoretical ValuesSO42-= 0.0352 M= 0.0334 0.0376 M (5% deviation)= 3.38 g/L= 3.21 3.55 g/L (5% deviation)6.2 Comparison of ResultsThe concentration of SO42- we obtained was 0.0345M and 3.31 g/L, which was within the 5% deviation range of 3.21 3.55 g/L. It was relatively close to the theoretical value of 3.38 g/L, at only a deviation of 2.11%.The results above show that the experiment was successful as the actual value was close to the theoretical value.6.3 Precautions TakenTo obtain the best results, BaSO4 crystals should be as large as possible. This facilitates filtration and washing of the crystals and the decreased surface area minimi zes the amount of impurities adsorbed onto the crystals. Generally, larger crystals are obtained when the rate of precipitation is lower. The rate of precipitation can be decreased by slightly increasing the solubility of BaSO4.To minimise the rate of precipitation, the following were doneAdding 5 drops of concentrated HCl. Adding HCl increases the solubility by lowering the pH. The solubility of BaSO4 at room temperature is around 0.3-0.4 mg per c g of water and increases when excessive amount of mineral acid is present. Additionally, precipitation should be done in an acidic medium as when done in neutral and basic mediums, Ba2+ ions precipitate with PO43-, CO32- or OH ions which are present in the solution. Addition of excess acid is avoided.Heating to boiling.Adding BaCl2 dropwise with vigorous stirring.At the end of the precipitation, a few drops of BaCl2 was added to the clear supernatant liquid to test for complete precipitation. After precipitation, suction filtration was p erformed. Suction filtration allows a higher rate of filtration by using a pressure gradient created by the aspirator. The precipitate was washed with deionised water and dried in the oven. It was then placed in a desiccator. The function of a desiccator is to despatch moisture from a substance or to protect a substance from moisture, thus preventing water from the humidity in the environment to react with the substance.6.4 Sources of Error6.4.1 CoprecipitationCoprecipitation is a process in which normally soluble compounds are carried out of solution by a precipitate. There are four types of Coprecipitation surface adsorption, mixed-crystal formation, occlusion and mechanistic entrapment. Surface adsorption and mixed-crystal formation are equilibrium processes, and occlusion and mechanical entrapment arise from the kinetics of crystal growth.Coprecipitation impurities may cause either negative or positive errors in an analysis. If the contaminant is not a compound of the ion bein g determined, a positive error will always result. In contrast, when the contaminant does contain the ion being determined, either positive or negative errors may occur.6.4.2 Surface AdsorptionAdsorption is very much the major source of contamination in grumous colloids (large specific surface areas) but of no significance in crystalline precipitates. Although adsorption does occur in crystalline solids, its forcefulness on purity are usually undetectable because of the relatively small specific surface area.Coagulation of a colloid does not significantly decrease the amount of adsorption because the coagulated solid still contains large internal surface areas that remain exposed to the solvent. The coprecipitated contaminant on the coagulated colloid consists of the lattice ion originally absorbed on the surface forward coagulation plus the counter-ion of opposite charge held in the film of solution immediately adjacent to the particle. The net effect of surface adsorption is the carrying down of an other soluble compound as a surface contaminant.6.4.3 Mixed-Crystal FormationIn mixed-crystal formation, which is too known as inclusion, one of the ions in the crystal lattice of a solid is replaced by an ion of another element. For this to occur, the deuce ions must gestate the same charge and their sizes must differ by no more than 5%. Furthermore, the two salts must belong to the same crystal class.The extent of mixed-crystal contamination is governed by the law of mass action and increases as the ratio of contaminant to analyte concentration increases. miniscule can be done about it when certain combinations of ions are present in a sample matrix. This problem occurs with both colloidal suspensions and crystalline precipitates. When this occurs, the officious ion may have to be separated before the final precipitation step. Alternatively, a different precipitating reagent that does not give mixed crystals with the ions in examination may be used.6.4 .4 Occlusion and Mechanical EntrapmentWhen a crystal is growing rapidly during precipitate formation, foreign ions in the counter-ion layer may become trapped, or occluded, within the growing crystal. Because supersaturation and thus growth rate decreases as precipitation progresses, the amount of occluded material is greatest in that part of a crystal that forms first.Mechanical entrapment occurs when crystals lie close together during growth. Several crystals grow together and in so doing trap a portion of the solution in a tiny pocket.Both occlusion and mechanical entrapment are at a minimum when the rate of precipitation formation is low, under conditions of low supersaturation. In addition, digestion often reduces the effects of these types of coprecipitation. The rapid dissolving and reprecipitation that occur at the elevated temperature of digestion open up the pockets and allow the impurities to escape into the solution.6.4.5 PeptisationPeptisation is the process by which a coagulated colloid reverts to its original dispersed state. When a coagulated colloid is washed, some of the electrolyte responsible for its coagulation is leached from the internal liquid in contact with the solid particles. Removal of this electrolyte has the effect of increasing the volume of the counter-ion layer. The repulsive forces responsible for the original colloidal state are then re-established, and particles detach themselves from the coagulated mass. The washings become cloudy as the freshly dispersed particles pass through the filter.Washing is needed to minimised contamination but there is a risk of losses resulting from peptisation if pure water is used. This is usually solved by washing the precipitate with a solution containing an electrolyte that volatilises when the precipitate is dried or ignited.6.4.6. PostprecipitationPost precipitation occurs when the top of the precipitate, which is in contact with the mother liquor is contaminated by precipitation of impu rities. This may be due to the primary adsorption of the common ion in excess, whereby the supersaturated solution of the second material is formed on the surface of the particle which offers nucleation sites to break supersaturation and causes a secondary precipitate to form.6.5 Improvements6.5.1 Minimising Adsorbed Impurities on ColloidsThe purity of many coagulated colloids is improved by digestion. Digestion is a process in which a precipitate is heated in the solution which is was formed (the mother liquor) and allowed to stand in contact with the solution. During digestion, water is expelled from the solid to give a denser mass that has a smaller specific surface area for adsorption.Washing a coagulated colloid with a solution containing a volatile electrolyte is also helpful because any non-volatile electrolyte added earlier to cause coagulation is displaced by the volatile species. Washing generally does not remove much of the primarily adsorbed ions because the attraction b etween these ions and the surface of the solid is too strong. Exchange occurs, however, between existing counter-ions and ions in the wash liquid.6.5.2 ReprecipitationAn effective way to minimise the effects of adsorption is reprecipitation. Reprecipitation adds substantially to the time required for an analysis. In this process, the filtered solid is redissolved and reprecipitated. The first precipitate carries down a fraction of the contaminant present in the original solvent. Thus, the solution containing the redissolved precipitate has a significantly lower contaminant concentration than the original, and even less adsorption occurs during the second precipitation.6.5.3 Precipitation from Homogenous SolutionPrecipitation from homogenous solution is a technique in which a precipitating agent is generated in a solution of the analyte by a slow chemical reaction. Local reagent excesses do not occur because the precipitating agent appears gradually and homogenously throughout the so lution and reacts immediately with the analyte. Thus, relative supersaturation is kept low during the entire precipitation and homogenously formed precipitates are better suited for analysis. This results in marked increase in crystal size as well as improvements in purity.In a nutshell, the experiment was a success and the results obtained were desirable. According to the results, the concentration of SO42- we obtained was 0.0345M and 3.31 g/L, which was close to the theoretical value of 3.38 g/L, at only a deviation of 2.11%. Although there may have been various possible sources of error, we have minimised them by lowering the rate of precipitation. The amount of sulfate was successfully determined by gravimetric analysis.A. V. Kasture , H. N. More, K. R. Mahadik , S. G. Wadodkar. 2008. Pharmaceutical Analysis Vol. I. Pragati Books Pvt. Ltd.Braun, R.D. 1982, existence to chemical analysis, McGraw-Hill, New York.Cammack, R. 2006, Oxford dictionary of biochemistry and molecular b iology, Oxford University Press Oxford, OxfordErdey, L., Belcher, R. Gordon, L. 2013, Gravimetric Analysis International Series of Monographs in Analytical alchemy, Vol. 7, Pergamon, Burlington.Skoog, D.A. 2014, Fundamentals of analytical chemistry, Brooks/Cole, Cengage Learning, Australia.Davidson College Chemistry Resources. Gravimetric Analysis online. Available from http//www.chm.davidson.edu/ronutt/che115/ VIII_gravi.pdf Accessed 20 December 2014Middle East Technical University. Gravimetric Determination of Sulfate in a Soluble hear online. Available from http//www.metu.edu.tr/chem223/sulfate.pdf Accessed 20 December 2014Santa Monica College. Gravimetric Analysis online. Available from http//www.smc.edu/projects/28/Chemistry_11_Experiments/Gravimetric_Analysis_Procedure.pdf Accessed 20 December 2014Texas AM University. Gravimetric Analysis online. Available from https//www.chem.tamu.edu/class/big league/tutorialnotefiles/gravimetric.htm Accessed 20 December 2014